4 Layer Flexible PCB Built on Polyimide with 2 oz Copper and
Immersion Gold plus Keypads for Mobile Devices
(FPC’s are custom-made products, the picture and parameters shown
are just for reference)
General description
This is a type of 4 layer flexible printed circuit for the
application of Electronic Counter. The base laminate is from ITEQ,
It’s fabricated per IPC 6012 Class 2 using supplied Gerber data.
Polyimide stiffener is applied on the inserting part.
Parameter and data sheet
| Size of Flexible PCB | 50.22 X 122.17mm |
| Number of Layers | 4 |
| Board Type | Flexible PCB |
| Board Thickness | 0.25mm |
| Board Material | Poyimide 25µm |
| Board Material Supplier | ITEQ |
| Tg Value of Board Material | 60℃ |
|
| PTH Cu thickness | ≥20 µm |
| Inner Iayer Cu thicknes | N/A |
| Surface Cu thickness | 70 µm |
| |
| Coverlay Colour | Yellow |
| Number of Coverlay | 1 |
| Thickness of Coverlay | 25 µm |
| Stiffener Material | Polyimide |
| Stiffener Thickness | 0.2mm |
| |
| Type of Silkscreen Ink | IJR-4000 MW300 |
| Supplier of Silkscreen | TAIYO |
| Color of Silkscreen | White |
| Number of Silkscreen | 1 |
|
| Peeling test of Coverlay | No peelable |
| Legend Adhesion | 3M 90℃ No peeling after Min. 3 times test |
|
| Surface Finish | Immersion Gold |
| Thickness of Nickle/Gold | Au: 0.03µm(Min.); Ni 2-4µm |
| RoHS Required | Yes |
| Famability | 94-V0 |
|
| Thermal Shock Test | Pass, -25℃±125℃, 1000 cycles. |
| Thermal Stress | Pass, 300±5℃,10 seconds, 3 cycles. No delamination, no blistering. |
| Function | 100% Pass electrical test |
| Workmanship | Compliance with IPC-A-600H & IPC-6013C Class 2 |
Features and benefits
Excellent flexibility
Reducing the volume
Weight reduction
Consistency of assembly
Increased reliability
Material optionality
Low cost
Continuity of processing
Diversified shipping method
Eligible products rate of first production: >95%
Applications
LCD module, mobile phone antenna flex board, consumer card reader
soft board
Components of a Flexible Circuit
A flexible circuit consists of copper foil, dielectric substrate+ coverlay and adhesive.
Copper foil is available in two different types of copper: ED Copper and RA
copper.
ED copper is an electro-deposited (ED) copper foil produced in the
same way as the copper foil used for rigid printed circuit boards.
This also means that the copper is “treated”, i.e., it has a
slightly rough surface on one side, which ensures a better adhesion
when the copper foil is bonded to the base material.
RA copper is a rolled and annealed copper foil produced from
electrolytically deposited cathode copper, which is melted and cast
into ingots. The ingots are first hot-rolled to a certain size and
milled on all surfaces. The copper is then cold-rolled and
annealed, until the desired thickness is obtained.
Copper foil is available in thickness of 12, 18, 35 and 70 μm.
The most common available for dielectric substrate and coverlay is polyimide films. This material can also be used as coverlay.
Polyimide is best suited for flexible circuits because of its
characteristics as stated below:
High temperature resistance allows soldering operations without
damaging the flexible circuits
Very good electrical properties
Good chemical resistance
Polyimide is available in thicknesses of 12.5, 20, 25 and 50 μm.
Base laminates for rigid printed circuit boards are copper foils
laminated together with the base materials, the adhesive coming from the prepreg material during lamination. Contrary to this is the flexible circuit where
the lamination of the copper foil to the film material is achieved
by means of an adhesive system. It is necessary to distinguish
between two main systems of adhesive, namely thermoplastic and
thermoset adhesives. The choice is dictated partly by the
processing, and partly by the application of the finished flexible
circuit.
